2024-26 Charger Rear Brake & Reverse Light Tint Overlay (Pre-Cut) Fits SixPack & EV

 Transform your 2024-26 Dodge Charger with our pre-cut rear tail light overlays. Choose from a range of bold tint colors to give your brake and turn signal lights an aggressive, head-turning look. These overlays darken your lights without sacrificing visibility, ensuring you stay bright and noticed even with the darkest shades. Unleash a fierce style that demands attention on every drive.

🔧 Specifications:

• Fitment: For 2024-26 Charger SixPack & EV
• High-Quality Material: Can withstand all kinds of weather (5 - 7 Year Durability)
  
• Easy Application (Peel and Stick)
  
• Comes in 8 x pieces of pre-cut tint overlay
• ** NOTE ** Not an actual brake light / turn signal replacement, this is a PRE-CUT OVERLAY TINT VINYL that sticks onto the existing housing.

🛠️How to Install:

For Best Results PROFESSIONAL INSTALLATION RECOMMENDED!
Tools Needed: Heat gun or blow dryer, padded glove or felt-tip squeegee

Step-by-Step Installation:

1. Rinse the entire area that you would like to apply this overlay with 70% isopropyl alcohol to remove all debris before application.

2. Dry the entire section before installation, ensuring there is no dust or debris on the surface.

3. Start with the Turn Signal first - you can align the bottom portion of the turn signal first or vice versa. However, we recommend the bottom so that the top portion will overlay the bottom which will prevent lifting of the tint in the future.
   

   1. Align the curved edge of tint that points toward the outside of the vehicle which is closest to the inner running brake lights.
   2. Once aligned it should fall into place, however, keep the tint just at the edge of the clear where the black painted portion meets the clear.
   3. The tint will warp slightly to fit the bump that sticks out towards you, the tint will cover maybe about half of the bump and the top tint will wrap down and slightly go over the bottom tint that you have wrapped already.
   4. Once desired placement is met, make sure you heat up the overlay so that it sticks strongly to the housing, due to the warping of the tint from the bump, the tint will need extra care to ensure tackiness.
      
      
4. Next - lay the top portion of the Turn Signal by aligning the curved edge that points towards the middle of the rear bumper. You can either start with the top tint or the bottom, however, we recommend the bottom tint so that the top will overlay and prevent lifting in the future.
    
   1. Align the curved edge of tint that points toward the middle of the vehicle which is closest to the rear emblem.
   2. Once aligned it should fall into place, however, keep the tint just at the top edge of the clear where the black painted portion meets the clear.
   3. The tint will warp slightly to fit the bump that sticks out towards you, the tint should cover over the bottom tint that was already installed prior to the top tint.
   4. Once desired placement is met, make sure you heat up the overlay so that it sticks strongly to the housing, due to the warping of the tint from the bump, the tint will need extra care to ensure tackiness.
      
      
5. Next-install reverse light overlay and follow the steps from 3 and 4 as they will work for the reverse light.
   

6. Continue laying the overlay till it is smoothed down on all parts of the flat surface until the desired placement has been met. (REFER TO PRODUCT PICTURES FOR ACCURATE PLACEMENT)
   

7. Once everything is laid to your desired outcome follow the below steps to ensure longevity and adhesion.

8. Post-heat the vinyl: Use a heat gun or blow dryer to remove small bubbles and activate the adhesive for stronger bonding.

9. If bubbles remain, press firmly with your finger or squeegee and swipe them out toward the closest edge.

📌 Reminder: Always post-heat the vinyl after installation. This activates the glue and ensures maximum adhesion. 

LIGHT SMOKE, DARK SMOKE, JDM YELLOW, BLUE - Please install dry method

All other colors - best to install wet (soapy water) if not adept at installing dry.